Technor RMS Series

Overview

RMS series lighting fixtures are ideally suited for ON and OFF-SHORE applications and all kinds of industries where there is an high level of corrosion. Both body and glass frame are made of stainless steel AISI304 and manufactured from a single sheet of steel with no invasive mounting holes, to minimize the risk of water ingress through the housing. Out of holes for power supply cable, whatever protected by a suitable cable gland (available upon request), there are no passing through holes between inside and outside of luminaire. Therefore during the time there is no risk of IP rating decrease as it would be possible where, for fi xing devices, there are through holes and relevant gaskets.

Design has been studied to allow operator working with free hands and no need to support any part of lighting fixture. One person can take care of start-up or maintenance without any aid and assistance. Due to inorganic materials like stainless steel and glass, RMS.. series lighting fi xtures are 95% recyclable; only components and insulation of single core wires need some more care.

Bildunterschrift

Technical Details

Model RMS 540 RMS 550 RMS 560
Light source RMS series lighting fixtures are suitable for two pins fluorescent lamps G13 socket Philips
TL-D or equivalent (lamps excluded)
RMS series lighting fixtures are suitable for two pins fluorescent lamps G13 socket Philips
TL-D or equivalent (lamps excluded)
RMS series lighting fixtures are suitable for two pins fluorescent lamps G13 socket Philips
TL-D or equivalent (lamps excluded)
Housing AISI304 stainless steel, 0,8mm thickness and transparent part in tempered glass (AISI316L
version available upon request)
AISI304 Stainless steel screws
AISI304 stainless steel, 0,8mm thickness and transparent part in tempered glass (AISI316L
version available upon request)
AISI304 Stainless steel screws
AISI304 stainless steel, 0,8mm thickness and transparent part in tempered glass (AISI316L
version available upon request)
AISI304 Stainless steel screws
IP Rating IP66 IP66 IP66
Emergency Version Available RMS.. lighting fixtures for emergency service of one tube:
- 90 minutes; guarantees 60’ duration with constant flux (emergency lumen factor 18%) and 30’ with decreasing flux
Available RMS.. lighting fixtures for emergency service of one tube:
- 90 minutes; guarantees 60’ duration with constant flux (emergency lumen factor 18%) and 30’ with decreasing flux
Available RMS.. lighting fixtures for emergency service of one tube:
- 90 minutes; guarantees 60’ duration with constant flux (emergency lumen factor 18%) and 30’ with decreasing flux
Ambient temperature -20 °C up to +60 °C -20 °C up to +55 °C -20 °C up to +60 °C
Voltage range 230 Vac 230 Vac 230 Vac
Systempower 1x 18W or 2x 18W or
1x 36W or 2x 36W
1x 18W or 2x 18W or
1x 36W or 2x 36W
1x 18W or 2x 18W or
1x 36W or 2x 36W
Power factor/Cos >0.9 >0.95 >0.95
Ballast Electromechanical ballast with starter and capacitor High frequency electronic ballast conforming with EN 60079 – 15 and IEC 60079 – 15 High frequency electronic ballast conforming with EN 60079 – 15 and IEC 60079 – 15
Gaskets Special cross-section tightness gasket, silicon rubber made (closed cell), located in housing
channel between body and window frame.
Special cross-section tightness gasket, silicon rubber made (closed cell), located in housing
channel between body and window frame.
Special cross-section tightness gasket, silicon rubber made (closed cell), located in housing
channel between body and window frame.
Entries Body complete of two 21mm Ø through holes (on one side) for cable entry, one complete of
metallic plug with M20 locknut and gasket and the other one with temporary plastic plug to prevent dust ingress.
Body complete of two 21mm Ø through holes (on one side) for cable entry, one complete of
metallic plug with M20 locknut and gasket and the other one with temporary plastic plug to prevent dust ingress.
Body complete of two 21mm Ø through holes (on one side) for cable entry, one complete of
metallic plug with M20 locknut and gasket and the other one with temporary plastic plug to prevent dust ingress.

Certificate Details

Model RMS 540 RMS 550 RMS 560
ATEX classification - Group II, Category 2, Gas and Dust Group II, Category 2, Gas and Dust
Area classification - Category 2 (Zone 1 and 21) Category 2 (Zone 1 and 21)
Certificate (ATEX) - INERIS 01ATEX3002X INERIS 01ATEX0060
Certificate (GOST R) - marking upon request, ordering code to be required marking upon request, ordering code to be required
Marking - {ex} II 3 GD
Ex-nA II T(**)
Ex-tD A22 IP66 T(**)
II 2 GD
Ex-de IIC T(**)
Ex-tD A21 IP65 T(**)
** T6/T85°C, T5/T100°C, T4/T135°C
CE Yes Yes Yes
According regulations Compliance with Electromagnetic Compatibility (EMC) according to European Directive
2004/108/CE
Compliance with Electromagnetic Compatibility (EMC) according to European Directive
2004/108/CE
Compliance with Electromagnetic Compatibility (EMC) according to European Directive
2004/108/CE

Optional

Model RMS 540 RMS 550 RMS 560
Pole mounting kit On request On request On request
Ceiling mounting kit On request On request On request
Suspension mounting kit On request On request On request
Wall mounting kit On request On request On request
3°- 4° through holes opposite side On request On request On request
Wiring with High frequency electronic ballast (220-240 V 50-60 Hz) On request Already included Already included